depend(0x00090000);

config(SUB, "系统配置", "系统的相关配置");
config(CHECK, "POWKEY 10s复位系统", "是否长按POWKEY 10s复位系统，用于防止系统死机", POWKEY_10S_RESET, 0);
config(LISTVAL, "自动休眠时间", "设置自动休眠时间", SYS_SLEEP_TIME, SHORT, 45, 21, ("不休眠", 0), ("10秒钟后", 10), ("20秒钟后", 20), ("30秒钟后", 30), ("45秒钟后", 45), ("1分钟后", 60), ("2分钟后", 120), ("3分钟后", 180), ("4分钟后", 240), ("5分钟后", 300), ("6分钟后", 360), ("7分钟后", 420), ("8分钟后", 480), ("9分钟后", 540), ("10分钟后", 600), ("15分钟后", 900), ("20分钟后", 1200), ("25分钟后", 1500), ("30分钟后", 1800), ("45分钟后", 2700), ("1小时后", 3600));
#config(LISTVAL, "自动关机时间", "设置自动关机时间", SYS_OFF_TIME, 	SHORT, 0, 18, ("不关机", 0), ("30秒钟后", 30), ("1分钟后", 60),  ("2分钟后", 120), ("3分钟后", 180), ("4分钟后", 240), ("5分钟后", 300), ("6分钟后", 360), ("7分钟后", 420), ("8分钟后", 480), ("9分钟后", 540), ("10分钟后", 600), ("15分钟后", 900), ("20分钟后", 1200), ("25分钟后", 1500), ("30分钟后", 1800), ("45分钟后", 2700), ("1小时后", 3600));
config(LIST, "音量级数", "选择系统音量级数", VOL_MAX, 2, "16级音量", "32级音量", 0);
config(BYTE, "开机默认音量", "开机默认音量级数", SYS_INIT_VOL, 0, 32, 8);
config(BYTE, "提示音播放音量", "提示音播放音量级数", WARNING_VOLUME, 0, 32, 8);
config(LIST, "OSC基础电容", "同时配置26M晶振OSCI与OSCO负载电容", OSC_BOTH_CAP, 2, "0PF", "6PF", 0);
config(BYTE, "自定义OSCI电容", "独立配置26M晶振OSCI负载电容，单位0.25PF。OSCI电容大小：n * 0.25PF + 基础电容", UOSCI_CAP, 0, 63, 23);
config(BYTE, "自定义OSCO电容", "独立配置26M晶振OSCO负载电容，单位0.25PF。OSCO电容大小：n * 0.25PF + 基础电容", UOSCO_CAP, 0, 63, 23);
config(CHECK,  "优先使用产测电容值",  "是否优先使用产测校准的OSC电容值，没过产测或者关闭时使用<自定义OSCI电容>、<自定义OSCO电容>",  FT_OSC_CAP_EN,  0);
config(CHECK, "EQ调试（蓝牙串口）", "是否使用SPP调试EQ功能", EQ_DGB_SPP_EN, 0);
config(CHECK, "EQ调试（UART）", "是否使用UART调试EQ功能", EQ_DGB_UART_EN, 0);
config(LISTVAL, "EQ调试串口选择", "选择调试串口的IO", EQ_UART_SEL, BIT, 2, 0, 4, ("VUSB", 0), ("PA1", 1), ("PA7", 2), ("PB3", 3), EQ_DGB_UART_EN);

config(SUB, "电源配置", "电源的相关配置");
config(CHECK, "BUCK MODE", "是否设置为BUCK MODE", BUCK_MODE_EN, 0);
config(CHECK, "VDDBT省电容", "是否VDDBT省电容，只能LDO模式才能capless", VDDBT_CAPLESS_EN, 0);
config(LISTVAL, "VDDIO电压", "选择VDDIO电压", VDDIO_SEL, BIT, 4, 9, 6, ("3.1V", 7), ("3.2V", 8), ("3.3V", 9), ("3.4V", 10), ("3.5V", 11), ("3.6V", 12));
config(LISTVAL, "VDDBT电压", "选择VDDBT电压", VDDBT_SEL, BIT, 4, 12, 6, ("1.35V", 10), ("1.4V", 11), ("1.45V", 12), ("1.5V", 13), ("1.55V", 14), ("1.6V", 15));

config(SUB, "DAC配置", "DAC的相关配置");
config(LISTVAL, "DAC声道选择", "选择DAC的输出方式", DAC_SEL, BIT, 2, 1, 2, ("差分单声道", 0), ("单端单声道", 1));
config(LISTVAL, "VDDDAC电压", "选择VDDDAC电压", DACAUD_LDO_SEL, BIT, 3, 5, 8, ("2.5V", 0), ("2.6V", 1), ("2.7V", 2), ("2.8V", 3), ("2.9V", 4), ("3.0V", 5), ("3.1V", 6), ("3.2V", 7));
config(CHECK, "省VDDDAC方案", "是否VDDDAC Bypass，内部VDDDAC与VDDIO短接。", DACAUD_BYPASS_EN, 0);
config(LIST, "DAC最大音量", "配置系统最大模拟增益，自动调整模拟音量表。", DAC_MAX_GAIN, 8, "0DB", "-1DB", "-2DB", "-3DB", "-4DB", "-5DB", "-6DB", "-7DB", 0);
config(LIST, "通话最大音量", "配置通话时最大模拟增益，自动调整模拟音量表。", BT_CALL_MAX_GAIN, 8, "0DB", "-1DB", "-2DB", "-3DB", "-4DB", "-5DB", "-6DB", "-7DB", 0);

config(SUB, "充电配置", "充电功能的相关配置");
config(CHECK, "充电使能", "是否打开充电功能", CHARGE_EN, 1);
config(CHECK, "涓流充电使能", "是否使能涓流充电", CHARGE_TRICK_EN, 1, CHARGE_EN);
config(CHECK, "插入DC复位系统", "是否插入DC充电复位系统，用于防止系统死机", CHARGE_DC_RESET, 1, CHARGE_EN);
config(CHECK, "插入DC禁止软开机", "PWRKEY软开机，DC Online时，禁止软开机", CHARGE_DC_NOT_PWRON, 1, CHARGE_EN);
config(LISTVAL, "充电截止电流", "选择充电截止电流", CHARGE_STOP_CURR, BIT, 4, 5, 11, ("2.5mA", 1), ("5mA", 2), ("7.5mA", 3), ("10mA", 4), ("12.5mA", 5), ("15mA", 6), ("17.5mA", 7), ("20mA", 8), ("25mA", 10), ("30mA", 12), ("35mA", 14), CHARGE_EN);
config(LISTVAL, "恒流充电电流", "恒流充电电流", CHARGE_CONSTANT_CURR, BIT, 6, 19, 38, ("15mA", 2), ("20mA", 3), ("25mA", 4), ("30mA", 5), ("35mA", 6), ("40mA", 7), ("45mA", 8), ("50mA", 9), ("55mA", 10), ("60mA", 11), ("65mA", 12), ("70mA", 13), ("75mA", 14), ("80mA", 15), ("90mA", 17), ("100mA", 19), ("110mA", 21), ("120mA", 23), ("130mA", 25), ("140mA", 27), ("150mA", 29), ("160mA", 31), ("170mA", 33), ("180mA", 35), ("190mA", 37), ("200mA", 39), ("210mA", 41), ("220mA", 43), ("230mA", 45), ("240mA", 47), ("250mA", 49), ("260mA", 51), ("270mA", 53), ("280mA", 55), ("290mA", 57), ("300mA", 59), ("310mA", 61), ("320mA", 63), CHARGE_EN);
config(LISTVAL, "涓流充电电流", "涓流充电电流", CHARGE_TRICKLE_CURR,  BIT, 6, 5, 7, ("5mA", 0), ("10mA", 1), ("20mA", 3), ("25mA", 4), ("30mA", 5), ("35mA", 6), ("40mA", 7), CHARGE_TRICK_EN);

config(SUB, "蓝牙配置", "蓝牙的相关配置");
config(TEXT, "蓝牙名称", "手机上可以看到的蓝牙名称", BT_NAME, 32, "BT-BOX");
config(MAC, "蓝牙地址", "蓝牙的MAC地址", BT_ADDR, 6, 41:42:00:00:00:00, 41:42:00:00:00:FF, 41:42:00:00:00:01);
config(LISTVAL, "降低回连TXPWR", "是否降低回连TXPWR", BT_RF_TXPWR_RECON, BIT, 3, 0, 4, ("不降低", 0), ("降低3dbm", 1), ("降低6dbm", 2), ("降低9dbm", 3));
config(CHECK, "音乐播放功能", "是否支持蓝牙音乐播放功能", BT_A2DP_EN, 1);
config(CHECK, "音乐音量同步", "是否支持A2DP音量与手机同步", BT_A2DP_VOL_CTRL_EN, 1, BT_A2DP_EN);
config(CHECK, "通话功能", "是否支持蓝牙通话的功能", BT_SCO_EN, 1);
config(CHECK, "私密接听功能", "是否使用手动私密接听（切换到手机端接听）", BT_HFP_PRIVATE_EN, 1, BT_SCO_EN);
config(CHECK, "来电报号功能", "是否支持来电报号功能", BT_HFP_RING_NUMBER_EN, 1, BT_SCO_EN);
config(CHECK, "来电播放手机铃声", "打开此功能后，可以播放手机铃声，例如ios", BT_HFP_INBAND_RING_EN, 0, BT_SCO_EN);
config(CHECK, "串口功能", "是否支持蓝牙串口的功能", BT_SPP_EN, 1);
config(CHECK, "BLE控制功能", "是否支持BLE音乐控制的功能", BLE_EN, 0);
config(TEXT, "BLE名称", "手机上可以看到的BLE蓝牙名称", LE_NAME, 32, "LE-Remoter", BLE_EN);

config(SUB, "蓝牙RF配置", "蓝牙RF相关配置");
config(BYTE, "PA_GAIN0",  "PA_GAIN0",  RF_PA_GAIN, 0, 7, 7);
config(BYTE, "MIX_GAIN0", "MIX_GAIN0", RF_MIX_GAIN, 0, 7, 6);
config(BYTE, "DIG_GAIN0", "DIG_GAIN0", RF_DIG_GAIN, 20, 57, 55);
config(BYTE, "CAPTUNE_VL", "低channel CAPTUNE",  RF_CAPTUNE_VL, 0, 15, 7);
config(BYTE, "CAPTUNE_VH", "高channel CAPTUNE",  RF_CAPTUNE_VH, 0, 15,  6);

config(SUB, "MIC参数", "蓝牙MIC参数");
config(LISTVAL, "MIC偏置电路配置", "MIC电路BIAS配置，省电容配置", MIC_BIAS_METHOD, BIT, 2, 0, 2, ("None", 0), ("MIC省电容省电阻V2", 2));
config(LEVEL, 0x03);
config(LISTVAL, "MIC模拟增益", "MIC模拟增益配置", BT_ANL_GAIN, BIT, 4, 0, 15, ("0 (3DB)", 0), ("1 (6DB)", 1), ("2 (9DB)", 2), ("3 (12DB)", 3), ("4 (15DB)", 4), ("5 (18DB)", 5), ("6 (21DB)", 6), ("7 (24DB)", 7), ("8 (27DB)", 8), ("9 (30DB)", 9), ("10 (33DB)", 10), ("11 (36DB)", 11), ("12 (39DB)", 12), ("13 (42DB)", 13), ("14 (45DB)", 14));
config(BYTE, "MIC数字增益(0~32DB)", "MIC SDADC数字增益, Step 0.5DB", BT_DIG_GAIN, 0, 63, 0);
config(BIT, "MIC后置数字增益", "调节算法后置MIC数字增益", MIC_POST_GAIN, 4, 0, 15, 0, BT_SCO_EN);

config(SUB, "通话参数", "蓝牙的通话参数", BT_SCO_EN);
config(CHECK, "近端降噪", "是否使能近端降噪功能", BT_SCO_NR_EN, 1, BT_SCO_EN);
config(BIT, "近端降噪级别", "近端降噪深度, 值越大降噪越猛。", BT_SCO_NR_LEVEL, 5, 0, 19, 2, BT_SCO_NR_EN);
config(CHECK, "近端降噪去喇叭声", "近端降噪是否加强对车喇叭声的消除, 对音质有些影响。", BT_SCO_NR_TRUMPET_EN, 0, BT_SCO_NR_EN);
config(CHECK, "AEC功能", "是否支持AEC功能，AEC/ALC只能二选一", BT_AEC_EN, 1, BT_SCO_EN);
config(BIT, "AEC回声消除级别", "回声消除级别(级别越高，回声衰减越明显，但通话效果越差)", BT_ECHO_LEVEL, 4, 0, 15, 2, BT_AEC_EN);
config(BYTE, "AEC远端补偿值", "远端补偿值(0~255)", BT_FAR_OFFSET, 0, 255, 36, BT_AEC_EN);
config(CHECK, "ALC功能", "是否支持ALC功能，AEC/ALC只能二选一", BT_ALC_EN, 0, BT_SCO_EN);

config(SUB, "生产配置", "生产配置");
config(TEXT, "序列号前两个字节", "序列号前两个字节", SERIAL_2, 8, "ABAB");
config(MAC, "序列号", "烧录的序列号", SERIAL_NUM, 6, 00:00:00:00:00:01, 00:00:FF:FF:FF:FF, 00:00:00:00:00:01);

config(LEVEL, 0x0E);
config(SUB, "产测参数", "产测校准的一些参数，不要改动！");
config(KEEP);
config(BYTE, "产测OSCI电容", "产测校准的24M晶振OSCI负载电容，单位0.25PF。不要改动默认值0。", OSCI_CAP, 0, 63, 0);
config(BYTE, "产测OSCO电容", "产测校准的24M晶振OSCO负载电容，单位0.25PF。不要改动默认值0。", OSCO_CAP, 0, 63, 0);
config(KEEPEND)

config(LEVEL, 0x100);
makecfgfile(xcfg.bin);
makecfgdef(xcfg.h);
xcopy(xcfg.h, ../../xcfg.h);